CHF 21.95
Currently not available
CHF 21.95
Raspberry Pi camera HDMI cable adapter
Order now and secure 11 Berrys
Description
Product information "Raspberry Pi camera HDMI cable adapter"
With this kit, a standard HDMI cable can be used between the Raspberry Pi and a camera. The biggest advantages are the increase in range, the ability to use widely available cables and to use a round and robust HDMI cable instead of a ribbon cable. Note that this is only an extension between the camera and the Raspberry Pi. There are four extra pins available, this can be handy to use a couple of low power sensors along with your camera. This system works with all Raspberry Pi models.
The manufacturer has successfully tested simple 5 metre HDMI cables, cheap or expensive cables worked just as well. The video signal should show no degradation up to a certain distance (which is yet to be found), beyond this limit the video signal is completely lost. However, no HDMI boosters or HDMI conversion to CAT6 have yet been tested.
Installation instructions
The manufacturer has successfully tested simple 5 metre HDMI cables, cheap or expensive cables worked just as well. The video signal should show no degradation up to a certain distance (which is yet to be found), beyond this limit the video signal is completely lost. However, no HDMI boosters or HDMI conversion to CAT6 have yet been tested.
Installation instructions
- Installation is simple, but requires precision when placing and tightening the small M2 screws (4mm). To reproduce the assembly shown in the first picture:
- Fit the 60mm flat cable between the camera and the board, pay attention to the picture for the side of the cable; the connectors point away on the extension board and towards the camera.
- Snap in the connections, it helps to have long nails here. This is essential for a good connection.
- Place the boards back to back, the ribbon should form the shape of an "S".
- Using your fingers and possibly tweezers, loosely insert a screw and a spacer. Place another one on the opposite side and tighten it slightly. Then insert the remaining two screws and tighten everything with a small screwdriver and a 4 mm spanner or pliers. Et voila, you're done!
Properties
| Zolltarifnummer: | 84733080 |
|---|---|
| Brand: | Frei |
| Country of Origin: | Great Britain |
| EAN: | 0704256791995 |
| Gross Weight (kg): | 0.012 |
| Manufacturer ID: | PES001 |
| Product ID: | RPI-CC-HDMI |
Manufacturer and safety information
Manufacturer information
BerryBase GmbH
Bei den Mühren 70
DE 20457 Hamburg
https://www.berrybase.de
info@berrybase.de
Person responsible for the EU
See manufacturer information
Safety instructions
BerryBase GmbH
Bei den Mühren 70
DE 20457 Hamburg
https://www.berrybase.de
info@berrybase.de
Person responsible for the EU
See manufacturer information
Safety instructions
- Only use the camera in accordance with the manufacturer's instructions.
- Ensure that all cables are securely connected to prevent damage to the device or user.
- Protect the camera from moisture, extreme temperatures and direct sunlight.
- Switch off the Raspberry Pi before installing or removing the camera.
- Do not use the camera in safety-critical applications where failure could lead to damage.
- Protect electronic components from electrostatic discharge (ESD), e.g. by using a grounded wrist strap.
- Avoid contact with conductive materials while the camera is powered.
- Do not violate applicable data protection laws when using the camera.
- Only dispose of defective or damaged cameras at suitable collection points for electronic devices.
Hersteller- und Sicherheitsinformationen
Hersteller-Informationen
BerryBase GmbH
Bei den Mühren 70
DE 20457 Hamburg
https://www.berrybase.de
info@berrybase.de
Verantwortliche Person für die EU
Siehe Hersteller-Informationen
Sicherheitshinweise
BerryBase GmbH
Bei den Mühren 70
DE 20457 Hamburg
https://www.berrybase.de
info@berrybase.de
Verantwortliche Person für die EU
Siehe Hersteller-Informationen
Sicherheitshinweise
- Verwenden Sie die Kamera nur in Übereinstimmung mit den Anweisungen des Herstellers.
- Stellen Sie sicher, dass alle Kabel sicher angeschlossen sind, um Schäden an Gerät oder Benutzer zu vermeiden.
- Schützen Sie die Kamera vor Feuchtigkeit, extremen Temperaturen und direkter Sonneneinstrahlung.
- Schalten Sie den Raspberry Pi aus, bevor Sie die Kamera installieren oder entfernen.
- Verwenden Sie die Kamera nicht in sicherheitskritischen Anwendungen, in denen der Ausfall zu Schäden führen könnte.
- Elektronische Komponenten vor elektrostatischer Entladung (ESD) schützen, z. B. durch Nutzung eines geerdeten Armbands.
- Vermeiden Sie Kontakt mit leitenden Materialien, während die Kamera mit Strom versorgt wird.
- Verletzen Sie nicht geltende Datenschutzgesetze, wenn Sie die Kamera verwenden.
- Defekte oder beschädigte Kameras ausschließlich über geeignete Sammelstellen für Elektronikgeräte entsorgen.
Reviews 2
Login
2 reviews
27 March 2022 00:00
-
-
24 November 2021 00:00
-
-